Machines

Fully Refurbished Bollegraaf baler HBC110K (75kW) inluding crosswires HBC110K

Specifications

Machine

Type HBC110K
Power 75kW
Year 2006
Hours 0
Condition Fully refurbished including 2 yr warranty

Bale dimensions

Weight
Length
Height
Width

Motor

Output
Twistomat
Counter pressure pump
Needle installation
Oil cooler fan
Pump for oil cooling
Operating pressure

Max capacity

Volume mg/hour
Weight kg/m3
Weight t/hour

Highlights

  • Adaptive Channel Pressure System
  • Central Greasing System
  • Horizontal Crosswire System
  • New M340 PLC including latest software and touchscreen

Additional information

 Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler

Technical data baler
Manufacturer Bollegraaf
Typ HBC 110 K
Year of construction 2006
Press power main press 100 tons
Press power of pre-press 50 tons
Feed channel 1,600 x 1,100 mm
Capacity per cycle time 3,15 m³
Theoretic cycle time 19 sec.
Bale size 1,100 x 1,100 mm
Driving motor 75 kW
Connected load 126 kW
Full load current 238 A
Tying system 5-fold vertical, 5-fold horizontal, fully automated
Throughput rate at a
bulk weight of 30 kg/cbm approx.16 tons/h
bulk weight of 50 kg/cbm approx. 25 tons/h
bulk weight of 100 kg/cbm approx. 47 tons/h
Bale weight up to 1400 kg, depends on material and bale lenght
Volume oil tank approx. 1,300 l
SPS controller (manuf., type) Telemecanique TSX Micro
Operating panel (manuf., type) Schneider MAGELIS Touch
Baler dimensions built up with hopper 11,750 x 2,500 x 7,105 mm (l x w x h)
Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h)
Machine weight baler approx. 36 tons

Baler will be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This inclused 2 year guarrantee. Contact us for more information or a quotation.

General principles of refurbishment

Cleaning & disassembly
Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop.

Tolerances
After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components;
• Ram,
• Frame,
• Channel,
• Pre-press-flap

After disassembly and inspection the ram is welded-up again and fitted with new ram wheels.

The protective grids and the pre-press flap are made dent-free and repaired where necessary.

Repainted
After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again.

Hydraulics:
The hydraulic tank is cleaned.
The hydraulic lines & hoses are replaced.
The hydraulic components are repackaged.
The hydraulic oil is replaced.

Cabling:
All cabling is checked and replaced if necessary.
All junction boxes are replaced and placed back in easily accessible positions.

Wear parts:
All wearing parts are replaced.
The pins and shafts of the cylinders and the channel are replaced with new ones.
All wearing parts of (both) needle installations and knotters are replaced for new.

Cylinders:
The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod.

MCC Cabinet
The switch box is checked and cleaned.
If necessary, electronic components are replaced with new ones.
B2mltxy9v7
The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Bollegraaf OEM certified refurbishment proces

More information

Examples Refurbished Machines

OEM QUALITY COMPLIANCE SEAL

Disclaimer

Disclaimer - All information in this document has been provided with the greatest diligence. However, we cannot guarantee its accuracy or any
changes that may have occurred in the meantime. Therefore, any liability is expressly excluded. No part of this brochure may be reproduced or
transmitted in any form or by any means without our explicit and written permission – Bollegraaf Recycling Solutions.