Fully Refurbished Bollegraaf baler HBC100A (75kW) Bollegraaf HBC100



Type Bollegraaf HBC100
Power 75kW
Year 2003
Hours 0
Condition Fully refurbished including 2 yr warranty

Bale dimensions



Counter pressure pump
Needle installation
Oil cooler fan
Pump for oil cooling
Operating pressure

Max capacity

Volume mg/hour
Weight kg/m3
Weight t/hour


Additional information

Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler

Bollegraaf HBC100A Balenpers (75kW)
Weight: 34.200 kg
Construction year: 2003

Materials previously baled: paper & cardboard

Baler will be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This inclused 2 year guarrantee. Contact us for more information or a quotation.

Technical specifications of the baler, type HBC110F

Volume capacity m3/hour max. - 815 660 500
Volume weight kg/m3 max. - 20 50 100
Weight capacity T/hour max. - 16,3 33 50

Average material weight
20 kg/m³ plastic PET
35 kg/m³ plastic HDPE
50 kg/m³ Loose cardboard
100 kg/m³ loose newspaper / cardboard
200 kg/m³ magazines

The above mentioned capacities apply only if the machine is being used judiciously and has been sufficiently fed without interruptions for at least one hour with proper material.

Bale weight - till 1400 kg, depending on the type of material and bale length.
Bale length - Can be set.
Bale height - 720 mm.
Bale width - 1100 mm.

Hopper size - 1100 mm x 1600 mm - these dimensions also determine the size of the material that is put into the machine.

Pressure force ram - max. 95 tons.
Pressure force pre-press flap - max. 52 tons.

Cycle time, excl. wire knotting time - 19 seconds.
Motor output - 75 kW (100 HP).
Motor Twistomat (knotter) - 1.5 kW (-- HP)., SEW
Motor counter pressure pump - 1.1 kW (2 HP).
Motor needle installation - 7.5 kW (-- HP)., SEW
Motor oil cooler fan - 0.55 kW (0,74 HP).
Motor pump for oil cooling - 2.2 kW (2,95 HP).
Operating pressure - 250 bar.

Machine weight - approx. 37620 kg.
Number of wires - 5 vertical.
Oil quantity - 1423 liters.
Brand and type of oil - MOBIL Univis N46.
Color - baler RAL 6029 (mint green).
- safety grids RAL 1021 (cadmium yellow).

Baler dimensions - length 11765 mm;
- width 2500 mm;
- height 7104 mm.
Switch box

The switch box is placed to the rear left of the press on the floor.
No motor groups are incorporated in the switch box for the feed belts (if any). There is a potential-free contact for the belt control. 

The refurbishment process is done to our very strict OEM refurbishment guidelines. 
Bollegraaf OEM Factory-Certified Refurbished Balers: 
Only Bollegraaf can guarantee that a reconditioned baler is built according to factory standards. 
At our location in Appingedam we have a special overhaul workshop where we overhaul used balers. 
When you purchase a Bollegraaf OEM Factory-Certified Refurbished Baler, you can be sure the baler has been fully inspected and is as good as new. 
Remanufactured or used Bollegraaf balers from other companies do not undergo the same rigorous inspection and reconstruction.
General principles overhaul
Cleaning and disassembly
The baler is completely cleaned and dismantled in our overhaul workshop.
The tolerances of all steel components are measured and where necessary welded again.
At least this applies to;
  • Ram,
  • Frame,
  • Channel,
  • Pre-press flap
The ram is re-welded and fitted with new ram wheels.
The protective grids and the pre-pressure flap are made dent-free and repaired where necessary.
After measuring the tolerances and any repair and welding work, all components are repainted.
The hydraulic tank is cleaned.
The hydraulic lines & hoses are replaced.
The hydraulic components are repackaged.
The hydraulic oil is replaced.
All cabling is checked and replaced if necessary.
All junction boxes are replaced and placed back in easily accessible positions.
Wear parts:
All wear parts are replaced.
The pins and shafts of the cylinders and the channel are replaced with new ones.
All wearing parts of the (both) needle installations and knots are replaced by new ones.
The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod.
Control box
The switch box is checked and cleaned.
If necessary, electronic components are replaced with new ones.